取消
显示结果 
搜索替代 
您的意思是: 
cancel
6642
查看次数
28
有帮助
1
评论
jingjian
Spotlight
Spotlight
在日常工作、或者经常性的设备测试,经常会遇到忘记登录密码这种尴尬的事情,遇到这种情况也不可怕,不要慌,我们也有相关的应对方法。
CISCO SWITCH Ver7.17
Device detected on 0:6:0 after 0 msecs
Device detected on 0:1:1 after 0 msecs
Device detected on 0:1:0 after 0 msecs
MCFrequency 1600Mhz
Relocated to memory
Detected CISCO IOFPGA
Donner Present
MIFPGA Present
Code Signing Results: 0x0
Using Upgrade FPGA
Booting from Primary Bios
FPGA Revison : 0x3
FPGA ID : 0x1399840
FPGA Date : 0x20140828
Power Debug Register: 0x0
Reset Cause Register: 0x80000000
Boot Ctrl Register : 0xe0ff
FPGA Update Status : 0x20
Detected CISCO MIFPGA
Version 2.16.1240. Copyright (C) 2013 American Megatrends, Inc.
Board type 2
IOFPGA @ 0xc8000000
SLOT_ID @ 0xf
Aborting config file read and autoboot
No autoboot or failed autoboot. falling to loader
按住CTRL+C
输入如下命令
loader > cmdline recoverymode=1
启动kickstart
loader > boot n9000-dk9.7.0.3.I1.1.bin 注意:此步骤可以通过dir命令查看当前的版本
Booting n9000-dk9.7.0.3.I1.1.bin
Trying diskboot
Filesystem type is ext2fs, partition type 0x83
Image valid
Image Signature verification was Successful.
INIT: version 2Loading IGB driver ...
Installing SSE module ... done
Creating the sse device node ... done
Installing CCTRL driver for card_type 21 ...
Checking SSD firmware ...
Model=Micron_M550_MTFDDAT064MAY, FwRev=MU01, SerialNo=MSA183101K1
Checking all filesystems.......
Installing SPROM driver ...
Installing default sprom values ...
done.Configuring network ...
Installing veobc ...
Installing OBFL driver ...
blogger: nothing to do.
..done Tue Dec 19 05:15:51 UTC 2017
tune2fs 1.35 (28-Feb-2004)
Setting reserved blocks percentage to 0 (0 blocks)
Starting portmap daemon...
creating NFS state directory: done
starting 8 nfsd kernel threads: done
starting mountd: done
starting statd: done
Saving image for img-sync ...
Loading system software
INIT: Sending processes the TERM signal
Bad terminal type: "linux". Will assume vt100.
Cisco Nexus Operating System (NX-OS) Software
TAC support: http://www.cisco.com/tac
Copyright (C) 2002-2015, Cisco and/or its affiliates.
All rights reserved.
The copyrights to certain works contained in this software are
owned by other third parties and used and distributed under their own
licenses, such as open source. This software is provided "as is," and unless
otherwise stated, there is no warranty, express or implied, including but not
limited to warranties of merchantability and fitness for a particular purpose.
Certain components of this software are licensed under
the GNU General Public License (GPL) version 2.0 or
GNU General Public License (GPL) version 3.0 or the GNU
Lesser General Public License (LGPL) Version 2.1 or
Lesser General Public License (LGPL) Version 2.0.
A copy of each such license is available at
http://www.opensource.org/licenses/gpl-2.0.php and
http://opensource.org/licenses/gpl-3.0.html and
http://www.opensource.org/licenses/lgpl-2.1.php and
http://www.gnu.org/licenses/old-licenses/library.txt.
switch(boot)# conf t
Enter configuration commands, one per line. End with CNTL/Z.
switch(boot)(config)#
switch(boot)(config)# admin-password cisco@123
WARNING! Enabling local authentication for login through console due to password recovery
switch(boot)(config)#
switch(boot)(config)# exit
switch(boot)# load-nxos
Uncompressing system image: package:/isanboot/bin/images/sys Tue Dec 19 05:16:39 UTC 2017
blogger: nothing to do.
正常启动后,就可以使用修改后的密码进入交换机了,并且配置不会更改
评论
sxsure001
Spotlight
Spotlight
lollollollollol
入门指南

使用上面的搜索栏输入关键字、短语或问题,搜索问题的答案。

我们希望您在这里的旅程尽可能顺利,因此这里有一些链接可以帮助您快速熟悉思科社区:









快捷链接