取消
显示结果 
搜索替代 
您的意思是: 
cancel
8648
查看次数
6
有帮助
10
回复

请教2901路由器自环测试的问题

xy411381121
Spotlight
Spotlight
本帖最后由 xy411381121 于 2018-8-10 16:19 编辑
做自环测试的时候,正常情况应该是端口显示looped吧,为什么会出现端口被都down掉,并反复出现AIS日志?
120106pkws96kenxngo9jo.png
左边端口现象正常:
NetTime-WAIBU-R2#sho int ser 0/1/1:0
Serial0/1/1:0 is up, line protocol is up (looped)
Hardware is DSX1
Description: DZ
Internet address is 192.200.100.25/30
MTU 1500 bytes, BW 2048 Kbit/sec, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation HDLC, loopback not set
右边端口则被down掉,且反复出现AIS的日志
NetTime-WAIBU-R2#sho int ser 0/1/0:0
Serial0/1/0:0 is down, line protocol is down
Hardware is DSX1
Description: GY
Internet address is 192.200.100.21/30
MTU 1500 bytes, BW 2048 Kbit/sec, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation HDLC, loopback not set
*Aug 8 08:05:54.193: %CONTROLLER-5-UPDOWN: Controller E1 0/1/0, changed state to up
*Aug 8 08:05:55.601: %LINK-3-UPDOWN: Interface Serial0/1/0:0, changed state to up
*Aug 8 08:05:56.601: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/1/0:0, changed state to up
*Aug 8 08:05:59.193: %CONTROLLER-5-UPDOWN: Controller E1 0/1/0, changed state to down (AIS detected)
*Aug 8 08:06:01.193: %LINK-3-UPDOWN: Interface Serial0/1/0:0, changed state to down
*Aug 8 08:06:02.193: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/1/0:0, changed state to down
端口配置也都是同一种模版:
controller E1 0/1/0
channel-group 0 unframed
controller E1 0/1/1
channel-group 0 unframed
interface Serial0/1/0:0
description GY
ip address 192.200.100.21 255.255.255.252
interface Serial0/1/1:0
description DZ
ip address 192.200.100.25 255.255.255.252
请问为什么右边在做自环测试时,会出现AIS并端口down掉?
10 条回复10

13nash
Level 8
Level 8
自环有专门的线序,你查下

alan_huang
Level 1
Level 1
AIS detected 表示線路有問題,你做自环测试當然還是不會起來
你兩根線對調看有問題的端口能不能起來,如果可以起來跟電信業者對一下有問題那條線的framing linecode等參數有沒有批配

xy411381121
Spotlight
Spotlight
13nash 发表于 2018-8-13 13:43
自环有专门的线序,你查下

083916ovii3u9h3isadnvh.jpg
我们这里是这做本地样自环,两边竖着的是没自环,中间横着的是把自己的收发连起来,打环。

Mansur
Spotlight
Spotlight
我还没玩过这种测试,学一下

alan_huang
Level 1
Level 1
xy411381121 发表于 2018-8-14 08:40
我们这里是这做本地样自环,两边竖着的是没自环,中间横着的是把自己的收发连起来,打环。

兩根線對調測試過嗎?

xy411381121
Spotlight
Spotlight
alan_huang 发表于 2018-8-14 10:43
兩根線對調測試過嗎?

没有,因为这就跟光纤差不多,一根发数据,一根收数据,所以其实也没有左右之分

cruiseluo
Spotlight
Spotlight
在确认E1线是好的前提下检查一下 controller E1 0/1/0 的时钟设置,比对一下 controller E1 0/1/0 和 controller E1 0/1/1 的时钟设置是不是一样的,如果 controller E1 0/1/0 的时钟设置是取外部时钟可能会有问题。
比如:
route#show controllers e1
E1 0 is up.
Applique type is Channelized E1 - balanced
No alarms detected.
Version info of Slot 0: HW: 2, Firmware: 4, PLD Rev: 2
Manufacture Cookie is not programmed.
Framing is CRC4, Line Code is HDB3, Clock Source is Line Primary.

xy411381121
Spotlight
Spotlight
cruiseluo 发表于 2018-8-14 16:34
在确认E1线是好的前提下检查一下 controller E1 0/1/0 的时钟设置,比对一下 controller E1 0/1/0 和 con ...

都是使用的相同配置,下次去机房的时候,我试试这条show命令。谢谢了!
controller E1 0/1/0
channel-group 0 unframed
controller E1 0/1/1
channel-group 0 unframed

alan_huang
Level 1
Level 1
本帖最后由 alan_huang 于 2018-8-15 22:57 编辑
xy411381121 发表于 2018-8-14 16:29
没有,因为这就跟光纤差不多,一根发数据,一根收数据,所以其实也没有左右之分

我的意思是把左邊端口正常的那條線接過來看看是不是正常
兩條線路應該是同一個運營商吧?

cruiseluo
Spotlight
Spotlight
检查出现AIS告警的那个端口 controller E1 0/1/0 是否有设置 crc4,如果没有设置,那么进 controller E1 0/1/0,输入 framing crc4
入门指南

使用上面的搜索栏输入关键字、短语或问题,搜索问题的答案。

我们希望您在这里的旅程尽可能顺利,因此这里有一些链接可以帮助您快速熟悉思科社区:









快捷链接