pxhen 发表于 2018-2-5 10:51
撸主应该在51CTO上发过帖子,我也回复过
不能中断的,请排除以下几点
帮忙看看,这个信息显示是否被锁定
,始终都进不去ROMMON模式
System Bootstrap, Version 12.4(13r)T, RELEASE SOFTWARE (fc1)
Technical Support:
http://www.cisco.com/techsupportCopyright (c) 2006 by cisco Systems, Inc.
Initializing memory for ECC
.
c2811 platform with 262144 Kbytes of main memory
Main memory is configured to 64 bit mode with ECC enabled
Upgrade ROMMON initialized
program load complete, entry point: 0x8000f000, size: 0xcb80
program load complete, entry point: 0x8000f000, size: 0xcb80
program load complete, entry point: 0x8000f000, size: 0xe37164
Self decompressing the image : ####################################################################################################################################################### [OK]
Smart Init is enabled
smart init is sizing iomem
ID MEMORY_REQ TYPE
0003E7 0X003DA000 C2811 Mainboard
0X000021B8 Onboard USB
0X002C29F0 public buffer pools
0X00211000 public particle pools
TOTAL: 0X008AFBA8
If any of the above Memory Requirements are
"UNKNOWN", you may be using an unsupported
configuration or there is a software problem and
system operation may be compromised.
Rounded IOMEM up to: 10Mb.
Using 3 percent iomem. [10Mb/256Mb]
Port Statistics for unclassified packets is not turned on.
WIC slot is empty or does not support clock participate
%SYS-6-READ_BOOTFILE_SKIP: boot system flash:c2800nm-advipservicesk9-mz.123-14.T2.bin command is skipped
%SYS-6-BOOT_MESSAGES: Messages above this line are from the boot loader.
program load complete, entry point: 0x8000f000, size: 0xe37164
Self decompressing the image : ####################################################################################################################################################### [OK]
Smart Init is enabled
smart init is sizing iomem
ID MEMORY_REQ TYPE
0003E7 0X003DA000 C2811 Mainboard
0X000021B8 Onboard USB
0X002C29F0 public buffer pools
0X00211000 public particle pools
TOTAL: 0X008AFBA8
If any of the above Memory Requirements are
"UNKNOWN", you may be using an unsupported
configuration or there is a software problem and
system operation may be compromised.
Rounded IOMEM up to: 10Mb.
Using 3 percent iomem. [10Mb/256Mb]
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, 2800 Software (C2800NM-IPBASE-M), Version 12.4(3g), RELEASE SOFTWARE (fc2)
Technical Support:
http://www.cisco.com/techsupportCopyright (c) 1986-2006 by Cisco Systems, Inc.
Compiled Mon 06-Nov-06 02:36 by alnguyen
Image text-base: 0x400A1994, data-base: 0x41540000
Port Statistics for unclassified packets is not turned on.
Cisco 2811 (revision 49.46) with 251904K/10240K bytes of memory.
Processor board ID FHK1117F1HU
2 FastEthernet interfaces
2 Serial(sync/async) interfaces
DRAM configuration is 64 bits wide with parity enabled.
239K bytes of non-volatile configuration memory.
62720K bytes of ATA CompactFlash (Read/Write)
WIC slot is empty or does not support clock participate
no ip ips deny-action ips-interface