取消
显示结果 
搜索替代 
您的意思是: 
cancel
11620
查看次数
12
有帮助
10
回复

求助cisco AIR-AP1832I-H-K9C无法敲命令

xixideng61446
Level 1
Level 1
如上传的图
用consele线连接在cisco AIR-AP1832I-H-K9C 在crt上敲不了yes的命令输入法也切换成英文的了,去其他思科ap可以敲命令
希望大神帮帮我
1 个已接受解答

已接受的解答

如果不使用CLI?看看这个能不能初始化:
Starting the Initial Configuration Wizard
Procedure
Step 1
Boot the AP that has controller capability.
It will be a few minutes before the CiscoAirProvision SSID starts broadcasting after initially powering up the AP. Once the CiscoAirProvision SSID starts broadcasting, the AP's status LED start cycling through green, red, and amber.
Step 2
Connect the Wi-Fi-enabled laptop to the CiscoAirProvision SSID advertised by the AP, using Wi-Fi. The password is password.
The laptop gets an IP address from the subnet 192.168.1.0/24.
Step 3
Open a supported web browser and enter the URL mobilityexpress.cisco to reach the initial configuration wizard. The wizard starts by asking you to create an admin account.
On Apple clients, after connecting to the CiscoAirProvision SSID, the captive portal window may automatically open with the initial configuration wizard. You can use this window itself complete the initial configuration without opening a web browser.
Note
After connecting to the CiscoAirProvision SSID, upon opening a web browser you should be automatically redirected to mobilityexpress.cisco. If you are not automatically redirected, then you can manually enter the URL mobilityexpress.cisco or go to http://192.168.1.1, both of which redirect to the initial configuration wizard.
https://www.cisco.com/c/en/us/td/docs/wireless/access_point/mob_exp/83/user_guide/b_ME_User_Guide_83/b_ME_User_Guide_83_chapter_01000.html#task_273F476C3AEA4F56B207CD62A80051E3
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Rps-Cheers | If it solves your problem, please mark as answer. Thanks !

在原帖中查看解决方案

10 条回复10

如果不使用CLI?看看这个能不能初始化:
Starting the Initial Configuration Wizard
Procedure
Step 1
Boot the AP that has controller capability.
It will be a few minutes before the CiscoAirProvision SSID starts broadcasting after initially powering up the AP. Once the CiscoAirProvision SSID starts broadcasting, the AP's status LED start cycling through green, red, and amber.
Step 2
Connect the Wi-Fi-enabled laptop to the CiscoAirProvision SSID advertised by the AP, using Wi-Fi. The password is password.
The laptop gets an IP address from the subnet 192.168.1.0/24.
Step 3
Open a supported web browser and enter the URL mobilityexpress.cisco to reach the initial configuration wizard. The wizard starts by asking you to create an admin account.
On Apple clients, after connecting to the CiscoAirProvision SSID, the captive portal window may automatically open with the initial configuration wizard. You can use this window itself complete the initial configuration without opening a web browser.
Note
After connecting to the CiscoAirProvision SSID, upon opening a web browser you should be automatically redirected to mobilityexpress.cisco. If you are not automatically redirected, then you can manually enter the URL mobilityexpress.cisco or go to http://192.168.1.1, both of which redirect to the initial configuration wizard.
https://www.cisco.com/c/en/us/td/docs/wireless/access_point/mob_exp/83/user_guide/b_ME_User_Guide_83/b_ME_User_Guide_83_chapter_01000.html#task_273F476C3AEA4F56B207CD62A80051E3
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Rps-Cheers | If it solves your problem, please mark as answer. Thanks !

iliaodong
Level 1
Level 1
电脑端软件或者你的console线的问题

YilinChen
Spotlight
Spotlight
终端防真程序串口检查如下参数:
Flow control
DTR/DSR
RTS/CTS
XON/XOFF

xixideng61446
Level 1
Level 1
iliaodong 发表于 2020-1-20 14:20
电脑端软件或者你的console线的问题

因为我用consele线进其他cisco AIR-AP1832I-H-K9CAP都可以就是这台不行,我试过了consele线没问题电脑也没问题,我也把它初始化了还是不行~~:(:(

xixideng61446
Level 1
Level 1
YilinChen 发表于 2020-1-20 14:32
终端防真程序串口检查如下参数:
Flow control
DTR/DSR

在CRT
我只把这个勾上了RTS/CTS

xixideng61446
Level 1
Level 1
1540488497lcj 发表于 2020-1-21 07:48
如果不使用CLI?看看这个能不能初始化:
Starting the Initial Configuration Wizard
Procedure

他是有控制器的。。我进的那个页面就是控制器的页面。。:(:(

xixideng61446
Level 1
Level 1
1540488497lcj 发表于 2020-1-21 07:48
如果不使用CLI?看看这个能不能初始化:
Starting the Initial Configuration Wizard
Procedure

我进的页面就是控制器的页面。。:(:(

Rockyw
Spotlight
Spotlight
直接按Enter键都没反应吗?能不能通过Web界面访问?
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Rockyw | If it solves your problem, please mark as answer. Thanks !

Rockyw
Spotlight
Spotlight
楼主参考一下下面的文章看看。
SecureCRT串口传输下界面无法输入字符问题
https://blog.csdn.net/qq_22252423/article/details/79650331
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Rockyw | If it solves your problem, please mark as answer. Thanks !

LinusT
Cisco Employee
Cisco Employee
我之前也好像遇见过,我改的CRT里面的参数就好了
入门指南

使用上面的搜索栏输入关键字、短语或问题,搜索问题的答案。

我们希望您在这里的旅程尽可能顺利,因此这里有一些链接可以帮助您快速熟悉思科社区:









快捷链接