取消
显示结果 
搜索替代 
您的意思是: 
cancel
3916
查看次数
0
有帮助
5
回复

N7K模块故障,不熟悉,特来请教

IceFire_Ken
Level 1
Level 1
155555g1w91wtcodpo7j5p.png
请问这是什么故障?
如何解决?
5 条回复5

Problem: Xbar Error/C7010-FAB-1 in Power Down State
The C7010-FAB-1 is in a power down state and these errors appear:
%PLATFORM-3-EJECTOR_STAT_CHANGED: Ejectors' status in slot 13 has changed,
Left Ejector is OPEN, Right Ejector is CLOSE
%PLATFORM-3-EJECTOR_STAT_CHANGED: Ejectors' status in slot 13 has changed,
Left Ejector is OPEN, Right Ejector is OPEN
%PLATFORM-2-XBAR_REMOVE: Xbar 3 removed (Serial number XXX)

Xbar Ports Module-Type Model Status
--- ----- ----------------------------------- ------------------ ----------
3 0 Fabric Module N/A powered-dn
?
Xbar Power-Status Reason
--- ------------ ---------------------------
3 powered-dn failure(powered-down) since maximum number of bringups were exceeded
Alternatively, xbar ASIC errors appear:
%MODULE-4-MOD_WARNING: Module 15 (serial: XXX) reported warning due to
X-bar Interface ASIC Error in device 70 (device error 0xc4600248)
%OC_USD-SLOT15-2-RF_CRC: OC2 received packets with CRC error from MOD 15
through XBAR slot 3/inst 2
Root Cause
This issue is due to either a faulty or bad-seated xbar module, or a bad chassis slot.
Solution
Check the output of these commands:
show version
show module
show logging
show logging nvram
show module internal exception-log
show module internal event-history
show core
show system reset-reason
show environment | in xbar
show system internal platform internal event-history xbar X is xbar #
show system internal xbar-client internal event-history errors
show system internal xbar all
show system internal xbar event-history errors
Perform a hard reseat of the xbar module and check the status.
If the reseat fails, test xbar in another slot or test the same slot with another xbar module in order to ensure the chassis is fine.
Replace the faulty hardware based on the tests performed in steps 2 and 3.
https://www.cisco.com/c/en/us/support/docs/switches/nexus-7000-series-switches/118959-troubleshoot-hw-arch-nexus7000-00.html
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Rps-Cheers | If it solves your problem, please mark as answer. Thanks !

Walter.wu
Spotlight
Spotlight
Root Cause
This issue is due to either a faulty or bad-seated xbar module, or a bad chassis slot.
Solution
Check the output of these commands:
show version
show module
show logging
show logging nvram
show module internal exception-log
show module internal event-history
show core
show system reset-reason
show environment | in xbar
show system internal platform internal event-history xbar X is xbar #
show system internal xbar-client internal event-history errors
show system internal xbar all
show system internal xbar event-history errors
Perform a hard reseat of the xbar module and check the status.
If the reseat fails, test xbar in another slot or test the same slot with another xbar module in order to ensure the chassis is fine.
Replace the faulty hardware based on the tests performed in steps 2 and 3.
排错手册:
https://www.cisco.com/c/en/us/support/docs/switches/nexus-7000-series-switches/118959-troubleshoot-hw-arch-nexus7000-00.html
Cisco CCIE EI /CCNP DC
Vmware VCP
PMP
CISSP

18653465190
Spotlight
Spotlight
这个真不清除,跟着大神学习一下。

liu_zhimin
Spotlight
Spotlight
模块自检为通过,建议重新插拔,如果还有问题请RMA更换

Rockyw
Spotlight
Spotlight
就像2楼提供的信息所说的,可能是硬件有问题,按2楼提供的解决方案操作看看要不要更换硬件。
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Rockyw | If it solves your problem, please mark as answer. Thanks !
入门指南

使用上面的搜索栏输入关键字、短语或问题,搜索问题的答案。

我们希望您在这里的旅程尽可能顺利,因此这里有一些链接可以帮助您快速熟悉思科社区:









快捷链接