取消
显示结果 
搜索替代 
您的意思是: 
cancel
3260
查看次数
0
有帮助
3
回复

ASA5506 开启WIFI MODEL ONLY问题

seasonli72658
Spotlight
Spotlight
本帖最后由 seasonli72658 于 2019-11-5 10:50 编辑
ASA5506要怎么开启WIFI功能呢,我看5506上面有一个WIFI MODEL ONLY,我在官网上看要打session wlan console上面这个命令才可以进入AP,但是打不出来,session 后面只能打sfr,不能打wlan是怎么回事呢
1 个已接受解答

已接受的解答

Rockyw
Spotlight
Spotlight
楼主参考一下
Cisco ASA 5506-X Series Quick Start Guide
https://www.cisco.com/c/en/us/td/docs/security/asa/quick_start/5506X/5506x-quick-start.html#id_66976
Enable the Wireless Access Point (ASA 5506W-X)
The ASA 5506W-X wireless access point is disabled by default. Connect to the access point GUI so you can enable the wireless radios and configure the SSID and security settings.
Before you begin
This procedure requires you to use the default configuration.
Procedure
Step 1
On the computer connected to the ASA inside network, launch a web browser.
Step 2
In the Address field, enter http://192.168.10.2. You are prompted for the username and password.
Note
If you are unable to reach the access point, and the ASA has the default configuration and other networking issues are not found, then you may want to restore the access point default configuration. You must access the ASA CLI (connect to the ASA console port, or configure Telnet or SSH access using ASDM). From the ASA CLI, enter hw-module module wlan recover configuration . If you need to troubleshoot the access point further, connect to the access point CLI using the session wlan console command.
Step 3
Enter the username cisco and the password Cisco. The access point GUI appears.
Step 4
On the left, click Easy Setup > Network Configuration.
Step 5
In the Radio Configuration area, for each of the Radio 2.4GHz and Radio 5GHz sections, set the following parameters and click Apply for each section:
SSID
Broadcast SSID in Beacon
Universal Admin Mode: Disable
Security (of your choosing)
Step 6
On the left, click Summary, and then on the main page under Network Interfaces, click the hotlink for the 2.4 GHz radio.
Step 7
Click the Settings tab.
Step 8
For the Enable Radio setting, click the Enable radio button, and then click Apply at the bottom of the page.
Step 9
Repeat for the 5 GHz radio.
Step 10
For more information, see the following manuals:
For details about using the wireless LAN controller, see the Cisco Wireless LAN Controller Software documentation.
For details about the wireless access point hardware and software, see the Cisco Aironet 700 Series documentation.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Rockyw | If it solves your problem, please mark as answer. Thanks !

在原帖中查看解决方案

3 条回复3

Rockyw
Spotlight
Spotlight
楼主参考一下
Cisco ASA 5506-X Series Quick Start Guide
https://www.cisco.com/c/en/us/td/docs/security/asa/quick_start/5506X/5506x-quick-start.html#id_66976
Enable the Wireless Access Point (ASA 5506W-X)
The ASA 5506W-X wireless access point is disabled by default. Connect to the access point GUI so you can enable the wireless radios and configure the SSID and security settings.
Before you begin
This procedure requires you to use the default configuration.
Procedure
Step 1
On the computer connected to the ASA inside network, launch a web browser.
Step 2
In the Address field, enter http://192.168.10.2. You are prompted for the username and password.
Note
If you are unable to reach the access point, and the ASA has the default configuration and other networking issues are not found, then you may want to restore the access point default configuration. You must access the ASA CLI (connect to the ASA console port, or configure Telnet or SSH access using ASDM). From the ASA CLI, enter hw-module module wlan recover configuration . If you need to troubleshoot the access point further, connect to the access point CLI using the session wlan console command.
Step 3
Enter the username cisco and the password Cisco. The access point GUI appears.
Step 4
On the left, click Easy Setup > Network Configuration.
Step 5
In the Radio Configuration area, for each of the Radio 2.4GHz and Radio 5GHz sections, set the following parameters and click Apply for each section:
SSID
Broadcast SSID in Beacon
Universal Admin Mode: Disable
Security (of your choosing)
Step 6
On the left, click Summary, and then on the main page under Network Interfaces, click the hotlink for the 2.4 GHz radio.
Step 7
Click the Settings tab.
Step 8
For the Enable Radio setting, click the Enable radio button, and then click Apply at the bottom of the page.
Step 9
Repeat for the 5 GHz radio.
Step 10
For more information, see the following manuals:
For details about using the wireless LAN controller, see the Cisco Wireless LAN Controller Software documentation.
For details about the wireless access point hardware and software, see the Cisco Aironet 700 Series documentation.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Rockyw | If it solves your problem, please mark as answer. Thanks !

xuxiaoxunlxl
Level 1
Level 1
这是设么功能

wanhuaye
Level 1
Level 1
我也没有开起这个。是不是没有这功能???
入门指南

使用上面的搜索栏输入关键字、短语或问题,搜索问题的答案。

我们希望您在这里的旅程尽可能顺利,因此这里有一些链接可以帮助您快速熟悉思科社区:









快捷链接