取消
显示结果 
搜索替代 
您的意思是: 
cancel
11728
查看次数
4
有帮助
12
回复

咨询:N7K双引擎IOS不一致,有什么方法可以将IOS同步?

shanghaiyunji
Level 1
Level 1
要更换引擎,思科寄了一块备件引擎,插入后发现IOS不一致,SSO失败。
有什么方法可以将主引擎的IOS同步到被引擎上,让SSO生效?
12 条回复12

one-time
Level 13
Level 13
感谢您的提问!稍后会有小伙伴为您解答的!

lingyu-cheng
Level 1
Level 1
FTP手动传吧

您好!20金钱已经发送给您了,感谢您的回答!

huoran1234
Spotlight
Spotlight
N7K的话发现IOS不一致会自动同步的

您好!20金钱已经发送给您了,感谢您的回答!

Rockyw
Spotlight
Spotlight
1、戴上防静电手套。
2、关掉N7K电源并拔出原活动引擎。
3、重启N7K,若原备份引擎无问题,N7K理应正常启动。(若备用引擎进入ROMmon模式,则在ROMmon模式下升级IOS并执行下列步骤。若引擎无法启动则引擎硬件出现故障,更换新引擎。)
4、待N7K重启正常后,清空引擎配置文件,并再次关掉N7K电源,拔出此引擎。
5、插上第一次拔出的N7K原活动引擎,重启N7K。
6、待N7K完全重启后,插上原备份引擎,此时N7K会自动同步相关配置信息。
7、测试N7K冗余状态及工作状态。
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Rockyw | If it solves your problem, please mark as answer. Thanks !

您好!20金钱已经发送给您了,感谢您的回答!

one-time
Level 13
Level 13
您好!若您的问题已解决,请记得标记最佳答案!

captain1
Level 1
Level 1
你好,正常情况备引擎会自动去下载并同步配置,如果认为原因导致两边不一致,可以采取拔出或重启备引擎,让其在重启过程执行同步NXOS和配置的工作。

anchingma
Level 1
Level 1
本帖最后由 anchingma 于 2017-6-23 09:58 编辑
怪怪的~重複發了。

anchingma
Level 1
Level 1
本帖最后由 anchingma 于 2017-6-23 09:56 编辑
跟我們之前一模一樣,照著做就對了!
Replacing the Standby Supervisor Module in a Dual Supervisor System
You can nondisruptively replace standby supervisor module in a dual supervisor system.
To replace the standby supervisor module, follow these steps:
Step 1 Power down the standby supervisor module.
switch# out-of-service module 6
這個步驟最重要,一定要先讓standby SUP2 離線再拔。
Step 2 Replace the supervisor module. For information on replacing a supervisor module, see the Cisco Nexus 7000 Series Hardware Installation and Reference Guide.
Note The replacement supervisor module should boot from the active supervisor module after six minutes. Use the reload module slot-number force command to force the boot.
Step 3 Copy the kickstart image from the active supervisor module to the standby supervisor module.
switch# copy bootflash:n7000-s2-kickstart.6.2.16.bin
bootflash://sup-remote/n7000-s2-kickstart.6.2.16.bin
Step 4 Copy the system image from the active supervisor module to the standby supervisor module.
copy bootflash:n7000-s2-dk9.6.2.16.bin
bootflash://sup-remote/n7000-s2-dk9.6.2.16.bin
Step 5 Configure the standby supervisor boot variables.
boot kickstart bootflash:/n7000-s2-kickstart.6.2.16.bin sup-2
boot system bootflash:/n7000-s2-dk9.6.2.16.bin sup-2
Step 6 Save these changes to the startup configuration.
switch# copy running-config startup-config

raojp
Spotlight
Spotlight
楼主最后搞定了吗?
入门指南

使用上面的搜索栏输入关键字、短语或问题,搜索问题的答案。

我们希望您在这里的旅程尽可能顺利,因此这里有一些链接可以帮助您快速熟悉思科社区:









快捷链接