请选择 进入手机版 | 继续访问电脑版

设为首页 收藏本站
思科社区 关注
思科社区

   思科 CCO 登录 推荐
 找回密码
 立即注册

搜索
热搜: 邮件服务器
查看: 281|回复: 2

ASA5506 开启WIFI MODEL ONLY问题

[复制链接]
发表于 2019-11-4 15:29:47 | 显示全部楼层 |阅读模式
0可用金钱
本帖最后由 seasonli72658 于 2019-11-5 10:50 编辑

ASA5506要怎么开启WIFI功能呢,我看5506上面有一个WIFI MODEL ONLY,我在官网上看要打session wlan console上面这个命令才可以进入AP,但是打不出来,session 后面只能打sfr,不能打wlan是怎么回事呢

最佳答案

查看完整内容

楼主参考一下 Cisco ASA 5506-X Series Quick Start Guide https://www.cisco.com/c/en/us/td/docs/security/asa/quick_start/5506X/5506x-quick-start.html#id_66976 Enable the Wireless Access Point (ASA 5506W-X) The ASA 5506W-X wireless access point is disabled by default. Connect to the access point GUI so you can enable the wireless radios and configure the SSID and security settings. Before y ...
  • 1
  • 2
  • 3
  • 4
  • 5
  • 1
  • 2
  • 3
  • 4
  • 5
平均得分0 (0 评价)
发表于 2019-11-4 15:29:48 | 显示全部楼层
楼主参考一下
Cisco ASA 5506-X Series Quick Start Guide
https://www.cisco.com/c/en/us/td ... start.html#id_66976

Enable the Wireless Access Point (ASA 5506W-X)

The ASA 5506W-X wireless access point is disabled by default. Connect to the access point GUI so you can enable the wireless radios and configure the SSID and security settings.

Before you begin

This procedure requires you to use the default configuration.

Procedure

Step 1       
On the computer connected to the ASA inside network, launch a web browser.
Step 2       
In the Address field, enter http://192.168.10.2. You are prompted for the username and password.
Note        
If you are unable to reach the access point, and the ASA has the default configuration and other networking issues are not found, then you may want to restore the access point default configuration. You must access the ASA CLI (connect to the ASA console port, or configure Telnet or SSH access using ASDM). From the ASA CLI, enter hw-module module wlan recover configuration . If you need to troubleshoot the access point further, connect to the access point CLI using the session wlan console command.
Step 3       
Enter the username cisco and the password Cisco. The access point GUI appears.
Step 4       
On the left, click Easy Setup > Network Configuration.
Step 5       
In the Radio Configuration area, for each of the Radio 2.4GHz and Radio 5GHz sections, set the following parameters and click Apply for each section:
SSID
Broadcast SSID in Beacon
Universal Admin Mode: Disable
Security (of your choosing)
Step 6       
On the left, click Summary, and then on the main page under Network Interfaces, click the hotlink for the 2.4 GHz radio.
Step 7       
Click the Settings tab.
Step 8       
For the Enable Radio setting, click the Enable radio button, and then click Apply at the bottom of the page.
Step 9       
Repeat for the 5 GHz radio.
Step 10       
For more information, see the following manuals:
For details about using the wireless LAN controller, see the Cisco Wireless LAN Controller Software documentation.
For details about the wireless access point hardware and software, see the Cisco Aironet 700 Series documentation.
  • 1
  • 2
  • 3
  • 4
  • 5
  • 1
  • 2
  • 3
  • 4
  • 5
平均得分0 (0 评价)
发表于 3 天前 | 显示全部楼层
这是设么功能
  • 1
  • 2
  • 3
  • 4
  • 5
  • 1
  • 2
  • 3
  • 4
  • 5
平均得分0 (0 评价)
您需要登录后才可以回帖 登录 | 立即注册

本版积分规则

Archiver | 思科社区  

GMT+8, 2019-11-15 22:54 , Processed in 0.082487 second(s), 33 queries .

京ICP备09041801号-187

版权所有 :copyright:1992-2019 思科系统  重要声明 | 保密声明 | 隐私权政策 | 商标 |

快速回复 返回顶部 返回列表